CANON IR400S TREIBER WINDOWS 10

CANON IR400S DRIVER DETAILS:

Type: Driver
File Name: canon_ir400s_13433.zip
File Size: 28.0 MB
Rating:
4.77
14 (4.77)
Downloads: 15
Supported systems: Windows 2008, Windows XP, Windows Vista, Windows 7/8/10
Price: Free* (*Free Registration Required)

Download Now
CANON IR400S DRIVER



If the lifter is up, canon ir400s the sensor lever [1] of the paper supply position canon ir400s inside the compartment. Stop the lifter [2] when it is about 7 cm from the bottom plate of the compartment, and insert a hex wrench [4] into the hole in the lifter drive shaft [3] to prevent the shaft from rotating.

Canon IrS error code E

Removing the Lifter Cable deck front side plate 1 Open the compartment, and remove any paper. Removing the Lifter Cable deck rear 1 Open the compartment, and remove any paper. At this time, try to match the top face of the canon ir400s to the marking line on the left side late of the compartment to facilitate the work. Caution: If you fail to perform step 8the lifter cable will slack when you remove the lifter motor. Routing the Lifter Cable 1 Check to make sure that the lifter drive shaft and the lifter are held in position by a hex wrench [1] and screwdrivers [2], respectively. At this time, be sure to keep the lifter cable taut so that the long screwdrivers are slightly pulled up. Feeding System 1. Figure Caution: When mounting the deck pick-up unit [3], be sure to tighten the three screws shown in Figure first. Orientation of the Deck Pick-Up Roller When mounting the deck pick-up roller [1] at the front, be sure that the marking [2] on the collar silver is toward the front and the marking [3] on the side of the roller is toward the rear.

CANON IR400S TELECHARGER PILOTE

When mounting the pick-up roller [4] at the rear, be sure that the marking [5] on the side of the roller and the marking [6] on the collar gold are toward the rear. Removing the Deck Separation Roller 1 Disconnect the deck from the copier, and remove the two screws [1]; then, detach the separation roller support plate [2]. Caution: The urethane sponge used for the deck separation roller is pink initially, and changes in color to orange and then to yellow, faster if exposed to light. This is a characteristic of the urethane sponge, and there is no different in performance, and parts canon ir400s not identified by color.

Adjusting the Deck Separation Roller Pressure If double feeding or pick-up failure occurs when the deck is used as the source of paper, change the position of the deck separation roller pressure spring: If pick-up failure occurs, move the spring in the direction of A. If double feeding occurs, move the spring in the direction of B. Position of the Deck Pick-Up Roller Releasing Solenoid Before removing the deck pick-up roller releasing solenoid [1] from the support plate, take note of the positions of the two fixing screws [2] on the solenoid; or, mark the position of the solenoid on the support plate with a scriber. If you are replacing the solenoid on its own, be sure to secure it in its initial position.

Electrical System 1.

CANON IR400S DRIVERS FOR MAC

Removing the Open Switch PCB 1 Disconnect the deck from the copier, and push down the latch plate [2] of the compartment [1] to open the compartment. Figure Caution: When canon ir400s the upper front cover, be sure that it is not trapped by the open switch PCB and all connectors are connected correctly. Outline Table shows the major functions of the fixing assembly, whileg Figure shows the major parts of the assembly. Sub thermistor Main thermistor Cleaning belt Fixing motor Canon ir400s Fixing assembly inlet guide drive solenoid.

Fixing Drive Assembly Figure shows the drive system of the fixing assembly. Cleaning Belt Drive Solenoid SL5 The cleaning belt drive solenoid is driven a specific period of time after the registration paper sensor turns on, and it operates each time the trailing edge of paper moves past the fixing assembly. The number of times it turns on varies according to the size of paper, and the resulting number enables the detection of the length of the cleaning belt indicated by two different messages. When the copier enters servile mode while the display is on, it brings up the Warning screen, which may be closed by pressing the OK key.

For the service person, "Replace the Canon ir400s Belt.

Canon imageRUNNER 400

Replace the canon ir400s belt as needed. Note: The cleaning belt counter operates as part of the software, requiring initialization only after replacement of the cleaning belt. Error Code E The copier remains not ready while this code is indicated, requiring immediate servicing. Replace the cleaning belt. Fixing Assembly Inlet Solenoid SL6 The copier adjusts the height of the fixing assembly inlet guide to suit the selected paper size using the fixing assembly inlet solenoid to improve feeding.

xerox workcentre 5016 scannerCOPYRIGHT 1999 CANON INC. Printed in Japan Imprim au Japon
agere sv92pl tooRelated titles

Figure B5R exclusive to canon ir400s size Fixing assembly inlet solenoid SL6 Height of the fixing inlet guide The solenoid drive signal turns on only when Down the height of the fixing assembly inlet guide needs to be changed. A specific period of time after the registration clutch turns on immediately before paper moves into the fixing assemblySL6 pull signal turns on. When the trailing edge of paper leaves the internal delivery sensor, SL6 back signal turns on. Off normal Up. Controlling the Fixing Temperature 1. Details of Temperature Control The copier executes temperature control as follows according tot the environmental conditions at main power -on and the type of transfer medium.

The following table shows the control temperature and printing conditions in each mode: Outline of Temperature Control n Normal Mode Control temperature Standby Printing C C Effective temperature C Remarks When the temperature of the fixing roller has reached Canon ir400s, initial multiple rotation is executed for 5 sec, enabling printing operation. When the temperature of the fixing roller has reached C, initial multiple rotation is executed for 20 sec, enabling printing operation. For each job, initial multiple rotation is executed during the period from C to Canon ir400s.

Thick paper mode may be selected on the screen designed for the selection of manual feed paper size. Control temperature Standby Printing C C Effective temperature C Remarks When the temperature of the fixing roller has reached C, initial multiple rotation is executed for 5 sec, enabling printing operation.

A press on the Canon ir400s Power key canon ir400s start power save mode, lowering the fixing temperature to a specific level sleep state. Place thick paper in the special cassette, and select the Thick Paper icon in user mode.

Canon U.S.A., Inc. imageRUNNER S

Set thick paper on the multifeeder tray, and select Thick Paper. Protective Mechanism for the Fixing System To prevent overheating of the fixing heater, the copier is equipped with the protective mechanisms shown in Canon ir400s If the fax function board is installed, however, the copier will not turn off the canon ir400s power, since doing so would erase image data.At ppm, the imageRUNNER S standalone digital copier is an ideal mid- range solution for users requiring exceptional image quality and editing capability.

I replaced the fuser cleaning roller and the canon ir400s still pops up as soon as you turn the power on! Does anyone know if there is a reset code to reset this error? did you go into service mode and clear the error code???? if not that is what you have to do.

Relevant Posts